ASTM D – 11, “Standard Test Methods for Field Measurement of Surface locations and the arithmetic mean determined, Method C—A composite plastic. Designation: D – 03Standard Test Methods for Field Measurement of 3 Method C—A composite plastic tape is impressed into Method C—A These test methods are under the jurisdiction of ASTM Committee D01 on The sole. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile 1 of 8 standard.3 Method C—A special tape3 containing a compressible 6.

Author: Tule Faell
Country: Cape Verde
Language: English (Spanish)
Genre: Relationship
Published (Last): 12 February 2004
Pages: 202
PDF File Size: 19.10 Mb
ePub File Size: 14.71 Mb
ISBN: 269-4-13395-358-9
Downloads: 22719
Price: Free* [*Free Regsitration Required]
Uploader: Moogulkree

Information relating to testing the tensile adhesion strength of coatings applied to surfaces other than steel will be removed from D during revisions that are also planned for Leave a Reply Cancel reply Your email address will not be published.

The instruments described are readily portable and sufficiently sturdy for use in the field. The user reports the pull-off strength in psi or MPaand the location of the break in the coating system, i. Facility owners with demanding service environments may consider specifying a given set astm d4417 method c criteria for surface roughness above and beyond the standard peak-to-valley depthwhich astm d4417 method c translate to increased performance and reduced life cycle costs.

There are many revisions being considered by the subcommittee. Resistance to Graffiti The resistance of coatings to graffiti and the ability to remove graffiti from coated surfaces is of interest to owners of buildings and other structures, as graffiti artists continue to deface public and private property. Evaluating graffiti resistance on freshly applied coating as well as coating that has been artificially weathered in the laboratory.

As acknowledged in Dscoring can cause micro-cracking in the coating, which may cause diminished pull-off strengths.

Testing consists of securing a loading fixture to the coating surface with an adhesive. The specified minimum pull-off strength must also be carefully considered. Ina plan was astm d4417 method c to conduct a comprehensive interlaboratory study involving six coatings, six laboratories and five types of adhesion testing equipment.


In this case, the minimum adhesion requirement becomes variable. For Method C, there are various ranges of replica tape that can be employed.

Differences in Surface Profile Measurements: ASTM D4417- Method B vs. Method C

What is Surface Profile and Why is it Necessary? Astm d4417 method c email address will not be published. Note 1 — Optical microscope methods serve as a referee method for surface profile measurement methods A and B.

However, thick film coatings i. Link to Active This link will always route to the current Active version of the standard. See Figures 1314 While the test method is designed to quantify the adhesion strength of the applied coating system, the substrate beneath the coating cannot be ignored.

Leave this field empty. Total of seven possible cleaning materials rather than five. This is done because of evidence that coatings performance in any one small area is primarily influenced by the highest surface features in that area astm d4417 method c not by the average roughness. Many equipment manufacturers have developed loading fixtures with a larger surface area i.

The entire standard is being revised, and will include among other changes astm d4417 method c specific operating procedures for the various types of test equipment. These methods are used to determine the average distance between the tops of the peaks and the bottoms of the valleys on a prepared steel surface. DTest Method for Pull-off Strength of Coatings Using Portable Adhesion Testers, has been developed to uniformly assess coating adhesion in the laboratory, shop, zstm field. The subcommittee develops and maintains standard test methods, practices and guides relating to the performance, evaluation, specification, application and proper use of industrial protective coatings.

Typically, the higher the coating thickness the greater the surface profile depth. ASTM D contains three methods of measuring surface profile depth: Standards for Measurement of Surface Profile There are currently four primary standards for measurement of surface profile in astm d4417 method c surfaces.

While there is current activity on all 13 standards, this article focuses on five major tasks being undertaken by the subcommittee at this time. So scoring is likely necessary on thick-film systems applied to concrete when trying to determine if astm d4417 method c coating is firmly bonded to astm d4417 method c substrate.


Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: Method B depth micrometer incorporates a special spring-tension micrometer with a 1-inch 2. This method encompasses only one surface characteristic: Pull-Off Adhesion of Coatings The adhesion of a protective coating is a critical attribute that is related to performance.

Based on laboratory research conducted by Roper et.

The base of the sstm rests on the peaks of the surface profile while the cone-shaped point projects into the valley.

The method describes three different procedures for quantifying surface profile, including visual comparators Method A astm d4417 method c, depth micrometers Method B and replica tape Method C.

astm d4417 method c Models from a few gage manufacturers are available that conform to this standard. Scoring the Coating Cutting scoring through the coating prior to the attachment of the loading fixture has long been a controversial issue. Soluble salts like chloride, astm d4417 method c trapped beneath a newly applied coating, can draw water through the coating film by a process known as osmosis and cause blistering and underfilm corrosion.

Other trade organizations NACE International and the Society for Protective Coatings are jointly developing a guidance document on acceptable levels of soluble surface chloride, based on the coating type and prevailing service environment.

Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University

He has been employed by KTA for over 27 years. Some coatings manufacturers report the pull-off strength on their product data sheets, and some specifiers require minimum pull-off strength for qualifying coatings. Revisions to the entire test method are also in process.